OAR 333-060-0125
Inlets

(1)

Pool inlets must be provided, sized and arranged to produce a uniform circulation of water so as to maintain a uniform disinfectant residual throughout the pool.

(2)

There must be at least one inlet per 400 square feet of pool area or 10,000 gallons of water, whichever is greater.

(3)

Pools more than 50 feet wide and reverse flow pools must use floor inlet fittings uniformly spaced no more than 20 feet apart and within 15 feet of the sidewalls.

(4)

Grates must be designed so as to prevent entrapment of fingers.

(5)

All recirculation inlet fittings must be adjustable for rate of flow. Wall inlet fittings must be directional.

(6)

Inlet fittings must have tamper-proof screws that cannot be removed except with tools. Grates, vortex plates and inlet fittings must be in place whenever the pool is in use.

(7)

Direct potable water pool inlets must:

(a)

Be over-the-rim fill spouts with air gaps located under a diving board or beside grab rails;

(b)

Be through-the-wall fill lines located above the water level and equipped with an appropriate backflow prevention device installed per OAR 333-061-0071 (Backflow Prevention Assembly Installation and Operation Standards); or

(c)

Be directly connected to the recirculation water supply and equipped with reduced pressure device installed per OAR 333-061-0071 (Backflow Prevention Assembly Installation and Operation Standards) on the potable water supply adjacent to the connection with the pool recirculation water.

Source: Rule 333-060-0125 — Inlets, https://secure.­sos.­state.­or.­us/oard/view.­action?ruleNumber=333-060-0125.

333‑060‑0005
Purpose 333‑060‑0010
Adoption by Reference 333‑060‑0015
Definitions 333‑060‑0020
Compliance 333‑060‑0025
Approval to Construct 333‑060‑0030
Plans 333‑060‑0035
Licenses 333‑060‑0040
Conditional Licenses 333‑060‑0045
Maintenance and Modification 333‑060‑0050
Structural Stability 333‑060‑0055
Size 333‑060‑0060
Dimensions 333‑060‑0065
Finishes, Markings and Lifelines 333‑060‑0070
Illumination 333‑060‑0075
Ventilation 333‑060‑0080
Ladders, Recessed Steps and Stairways 333‑060‑0085
Diving 333‑060‑0090
Slides 333‑060‑0091
Waterpark Slides 333‑060‑0095
Elevated Lifeguard Chairs 333‑060‑0100
Life Saving Equipment 333‑060‑0105
Swimming Pool Enclosure 333‑060‑0110
Decks 333‑060‑0115
Overflow Systems 333‑060‑0120
Recirculation System 333‑060‑0125
Inlets 333‑060‑0128
Submerged Suction Outlets and Drains 333‑060‑0130
Piping 333‑060‑0135
Pumps 333‑060‑0140
Filters 333‑060‑0145
Pool Heaters 333‑060‑0150
Disinfectant and Chemical Feeders 333‑060‑0155
Meters and Gauges 333‑060‑0160
Equipment Room 333‑060‑0165
Ground Fault Interrupter 333‑060‑0170
Bathhouses and Sanitary Facilities 333‑060‑0175
Visitor and Spectator Areas 333‑060‑0180
Food Service 333‑060‑0185
Drinking Fountains 333‑060‑0190
Domestic Water Quality 333‑060‑0200
Pool Water Quality 333‑060‑0205
Operation and Maintenance 333‑060‑0206
Supervision — Limited-Use Pools 333‑060‑0207
Supervision — General-Use Pools 333‑060‑0208
Lifeguard Supervision & Training 333‑060‑0209
Pool Staff Training & Safety 333‑060‑0210
Pool Safety 333‑060‑0215
Signs 333‑060‑0220
Variance 333‑060‑0225
Instructional Use of Limited-Use Pools 333‑060‑0500
Wading Pools 333‑060‑0505
New Wading Pool Construction 333‑060‑0510
Existing Wading Pools 333‑060‑0515
Wading Pool Operation 333‑060‑0700
Enforcement 333‑060‑0705
Pool Closure Criteria
Last Updated

Jun. 8, 2021

Rule 333-060-0125’s source at or​.us