OAR 333-071-0580
Physical Environment Requirements


(1) Any person proposing to construct a new SICF or proposing to make certain alterations or additions to an existing SICF, must, before commencing new construction, alterations, or additions, comply with OAR chapter 333, division 675 and these rules.
(2) Only the portion of an existing SICF that is being altered or renovated and any impacted ancillary areas required to ensure full functionality of the SICF must meet the requirements in sections (4) through (7) of this rule.
(3) The following guidelines are adopted by reference as specified in sections (4) through (6) of this rule. Each SICF must also meet the requirements of state building and specialty codes in affect at the time of initial licensure.
(a) 2018, Facility Guidelines Institute (FGI), Guidelines for the Design and Construction of Hospitals; and
(b) 2018, FGI, Guidelines for the Design and Construction of Residential Health, Care and Support Facilities.
(4)(a) An applicant or a licensed SICF classified as a freestanding hospice facility shall comply with the following chapters of the 2018, FGI, Guidelines for the Design and Construction of Residential Health, Care and Support Facilities, adopted by reference including all references to part, subpart, sections, subsections, paragraphs, subparagraphs and appendices except as specified in subsections (4)(b) and (c) of this rule. References in FGI to “and/or” mean “or”.
(A) 1.1 – Introduction;
(B) 1.2 – Planning/Predesign Process;
(C) 1.3 – Site Selection;
(D) 1.4 – Design, Construction, and Commissioning Considerations and Requirements;
(E) 1.5 – Equipment;
(F) 2.1 – Site Elements;
(G) 2.2 – Design Criteria;
(H) 2.3 – Design Elements;
(I) 2.4 – Design and Construction Requirements;
(J) 2.5 – Building Systems; and
(K) 3.2 – Specific Requirements for Hospice Facilities.
(b) Section 2.3-4.2.2.4 of the 2018, FGI, Design and Construction of Residential Health, Care and Support Facilities, is not adopted by reference and does not apply under subsection (4)(a) of this rule.
(c) The following amendments or additions are made to the 2018, FGI, Guidelines for Design and Construction of Residential Health, Care and Support Facilities, as adopted and incorporated by reference under subsection (4)(a) of this rule. All references to part, subpart, sections, paragraphs, subparagraphs and appendices relate to the 2018, FGI, Guidelines for Design and Construction of Residential Health, Care and Support Facilities.
(A) Amend subsection 1.1-2.2.2 to read: "Standards set forth in the Guidelines for Design and Construction of Residential Health, Care, and Support Facilities shall be considered minimum and do not prohibit designing facilities and systems that exceed these requirements where desired by the governing body of the health, care, or support facility. Project submittal criteria shall comply with OAR 333-675-0000 (Submission of Project Plans and Specifications for Review)."
(B) Amend subsection 1.1-3.1.2.1 to read: "Where major structural elements make total compliance impractical or impossible, exceptions shall be considered in accordance with OAR 333-071-0260 (Waivers)."
(C) Delete paragraphs (3) through (7) and amend subsection 1.1-3.1.2.2 to read: "The following exceptions to the requirements in Section 1.1-3.1.1 (Compliance Requirements) shall be permitted provided they meet the criteria specified in OAR 333-675-0000 (Submission of Project Plans and Specifications for Review)(2) or (3) and do not reduce the level of health and safety in an existing facility. (1) Routine repairs and maintenance to buildings, systems, or equipment shall not require improvements to building features or systems. (2) Replacement of building furnishings and movable or fixed equipment shall only require improvements to building systems that serve that equipment and only to the extent necessary to provide sufficient capacity for the replacement."
(D) Amend subsection 1.1-3.1.4 to read: "Temporary Waivers. When parts of an existing facility essential to continued overall facility operation cannot comply with particular standards during a renovation project, a temporary waiver of those standards shall be permitted as determined by the authority having jurisdiction if resident, participant, or outpatient health and safety will not be jeopardized as a result. Reference OAR 333-071-0260 (Waivers) for requirements."
(E) Amend subsection 1.1-5.2.1 to read: “In the absence of state or local requirements, the project shall comply with approved nationally recognized building codes except as modified in the latest CMS adopted edition of NFPA 101: Life Safety Code and/or herein.”
(F) Amend subsection 1.2-2.1.2.1 to read: “The care provider shall be responsible for providing a functional program for each facility project to the project architect/engineer and the authority having jurisdiction (AHJ). (1) Findings and recommendations from the resident safety risk assessment (see Section 1.2-3) shall be addressed in the functional program.”
(G) Amend subsection 1.2-2.1.2.2 to read: "The functional program shall include an executive summary as well as detailed information about each operation conducted in the facility that will affect the physical setting design. Refer to OAR 333-675-0000 (Submission of Project Plans and Specifications for Review)(6) for additional requirements to be included in the functional program."
(H) Amend subsection 1.2-3.1.1.2 to read: “To support this goal, a resident safety risk assessment (RSRA) shall be developed and completed by an interdisciplinary team. A copy of the RSRA shall accompany construction documents submitted to the Oregon Health Authority, Facility Planning and Safety Program.”
(I) Delete subparagraph (e) in subsection A1.2-3.5.3.4(3).
(J) Amend subparagraph (b) in subsection A1.2-4.5.1 to read: “b. Window sill height should not exceed 3 feet (.91 meter) above the floor and should be above grade. Operable windows shall be designed to prevent accidental falls when sill heights are lower than 36 inches and above the first floor.”
(K) Amend subparagraph (i) in subsection A1.2-4.5.2.2 to read: “i. Water features. Where provided and where allowed per the RSRA, open water features should be equipped to safely manage water quality to protect occupants from infectious or irritating aerosols. See Section 2.1-3.6.3 (Outdoor Water Features) and appendix section A2.4-2.2.13 (Decorative water features) for additional information and requirements.”
(L) Amend subsection 2.1-3.6.3.2 to read: “Where provided and allowed by the resident safety risk assessment (RSRA) for facilities that serve special care populations, outdoor water features shall be designed with the care population in mind to provide safe and accessible environments.”
(M) Delete subparagraph (i) in subsection A2.2-4.2.1.
(N) Amend subparagraph (2)(a) in subsection 2.3-2.3.3.2 to read: “(a) Space for dining in accordance with the needs of the care population, including residents and participants who use resident-operated mobility devices. Provide a minimum of 28 square feet (2.60 square meters) for each resident or participant at one seating.”
(O) Amend subsection A2.3-2.3.3.2(2) to read: “Adult day care programs may require additional participant space based on the care population being served.”
(P) Amend paragraph (2) in subsection 2.3-4.2.2.1 to read: “(2) A medication room, a self-contained medication distribution unit, or other approaches acceptable to the authority having jurisdiction (AHJ) shall be permitted to be used for preparing, dispensing, and administering medications.”
(Q) Amend subsection 2.3-4.2.2.3 to read: “Self-contained medication distribution units, automated medication-dispensing stations, or mobile medication-dispensing carts. Where these or other systems approved by the AHJ are used, the following shall apply: (1) Location of such units shall be permitted at the staff work area, in the clean utility room, in an alcove. (2) Areas used for medication preparation and distribution by mobile cart shall include task-specific lighting.”
(R) Delete paragraphs (4) and (5) and amend subsection 2.3-4.5.3.4 to read: “Ice-making equipment and drinking water source. (1) Location of ice-making equipment in the food preparation area or in a separate room shall be permitted as long as the equipment is directly accessible to the food preparation area. (2) Ice-making equipment shall be cleanable. (3) Ice-making equipment shall be self-dispensing. (4) A filtered self-dispensing drinking water source shall be provided.”
(S) Amend subsection 2.4-2.2.4 to read: "Doors and Door Hardware. See the facility chapters in Parts 3 through 5 for requirements in addition to those in this section. Door type for residing patient bathing/toilet facilities and other single-user toilets subject to patient use. Rooms that contain bathtubs, sitz baths, showers, or toilets for patient use shall have one of the following: (1) Two separate doors (2) A door that swings outward (3) A door equipped with emergency rescue hardware (4) A sliding door".
(T) Amend subsection 2.4-2.2.6.2 to read: “Sill height. Windows in resident rooms, suites, and dwelling units shall have sills located no higher than 36 inches (91.44 centimeters) above the finished floor. Operable windows shall be designed to prevent accidental falls when sill heights are lower than 36 inches and above the first floor.”
(U) Amend paragraphs (1) and (2) in subsection 2.4-2.2.8.1 to read: “(1) The number and placement of hand-washing stations shall be determined as indicated in other sections and by the infection control risk assessment (ICRA). (2) If not required by other sections, hand sanitation dispensers shall be permitted to be used in lieu of hand-washing stations as determined by the ICRA.”
(V) Amend subsection 2.4-2.2.13 to read: “Decorative Water Features Provision of decorative water features shall be permitted in residential health, care, and support facilities where allowed by the RSRA.”
(W) In subsection A3.2-2.2.1.2(2):
(i) Amend subparagraph (b) to read: “b. Home-based hospice services. This hospice care model is ineligible for review within these guidelines as the hospice care either takes place in individual homes or in facilities under the regulation of State of Oregon, Department of Human Services (DHS). This model includes services that are brought to a resident living in an assisted living facility or independent living setting. Home-based hospice services are provided for residents who live in an independent or assisted living setting. Hospice services to be provided by a care and support facility, if any, should be identified during the functional programming process.”
(ii) Amend subparagraph (g) to read: “g. Nursing home-based hospice facilities. This hospice care model is ineligible for review within these guidelines as these facilities are regulated by the State of Oregon, Department of Human Services (DHS). This model follows hospice regulations and includes any number of beds housed in a nursing home setting. Nursing home-based hospice facilities provide end-of-life services and should be provided in a private room that includes adequate family space. Nursing homes should provide hospice services and related accommodations for residents and family.”
(X) Amend paragraph (3) in subsection 3.2-2.2.2.2 to read: "(3) Room size shall be 80 square feet for each residing patient in a double room and at least 100 square feet for each patient residing in a single room. Room size shall also be based on the care model and in-room furniture and clothing storage requirements."
(Y) Amend subsection 3.2-2.3.3.3 to read: “Recreation, lounge, and activity areas. Lounge areas shall be provided for resident and visitor use at a minimum of 15 square feet per resident being served.”
(Z) Amend subsection 3.2-2.3.6.2 to read: “Inclusion of a gas fireplace or other comparable heating elements shall be permitted in a family room where non-operable glass doors are used. These heating element surfaces may not exceed 120 degrees Fahrenheit when they are installed in locations that are subject to incidental contact by people or with combustible material.”
(AA) Amend subsection 3.2-4.5.3.1 to read: "Where an outside vendor is used to provide meals for a facility of 16 or more beds, the facility shall include dedicated space and equipment for a warming kitchen, including space for minimal equipment for preparation of breakfast, emergency, or after-hours meals. These facilities serving 16 or more beds shall comply with OAR 333-150-0000 (Food Sanitation Rule) (Food Sanitation Rules) including the provisions for commercial-grade equipment, space, and policies."
(BB) Amend subsection 3.2-4.5.4 to read: "Decentralized Kitchen Where food preparation is conducted on-site for 16 or more beds, the facility shall have dedicated non-public staff space and equipment for preparation of meals. See Section 2.3-2.3.4 (Resident and Participant Kitchen) for requirements. These facilities serving 16 or more beds shall comply with OAR 333-150-0000 (Food Sanitation Rule) (Food Sanitation Rules) including the provisions for commercial-grade equipment, space, and policies."
(CC) Amend paragraph (2) in subsection 3.2-4.6.2.2 to read: “(2) Washers/extractors. Washers/extractors shall be located between the soiled linen receiving and clean processing areas. Washers/Extractors shall provide a temperature of at least 160 degrees Fahrenheit for a minimum of 25 minutes or include use of a chemical disinfectant.”
(DD) Amend paragraph (3) in subsection 3.2-4.6.3.2 to read: “(3) Room(s) used for processing shall have a flushing-rim sink and a handwash sink.”
(5)(a) An applicant or a licensed SICF classified as a rehabilitation hospital shall comply with the following chapters of the 2018, FGI, Guidelines for the Design and Construction of Hospitals, adopted by reference including all references to part, subpart, sections, subsections, paragraphs, subparagraphs and appendices except as specified in subsections (5)(b) and (c) of this rule. References in FGI to “and/or” mean “or”.
(A) 1.1 – Introduction;
(B) 1.2 – Planning, Design, Construction, and Commissioning;
(C) 1.3 – Site;
(D) 1.4 – Equipment;
(E) 2.1 – Common Elements for Hospitals;
(F) 2.2 – Specific Requirements for General Hospitals;
(G) 2.6 – Specific Requirements for Rehabilitation Hospitals; and
(H) Part 3 – Ventilation of Hospitals.
(b) The following sections, paragraphs, subparagraphs or appendices of the 2018, FGI, Guidelines for Design and Construction of Hospitals are not adopted by reference and do not apply under subsection (5)(a) of this rule:
(A) A1.2-2.1.2.1;
(B) 1.2-2.1.2.3;
(C) 1.2-8.3 through 1.2-8.3.3;
(D) 2.1-2.8.10.2; and
(E) A2.1-8.3.3.1(2).
(c) The following amendments or additions are made to the 2018, FGI, Guidelines for Design and Construction of Hospitals, as adopted and incorporated by reference under subsection (5)(a) of this rule. All references to part, subpart, sections, paragraphs, subparagraphs and appendices relate to the 2018, FGI, Guidelines for Design and Construction of Hospitals.
(A) Amend section 1.1-2 to read: "New Construction Project submittal criteria shall comply with OAR 333-675-0000 (Submission of Project Plans and Specifications for Review). Projects with any of the following scopes of work shall be considered new construction and shall comply with the requirements in the Guidelines for Design and Construction of Hospitals:"
(B) Amend subsection 1.1-3.1.1.2 to read: "Major renovation projects. Project submittal criteria shall comply with OAR 333-675-0000 (Submission of Project Plans and Specifications for Review). Projects with either of the following scopes of work shall be considered a major renovation and shall comply with the requirements for new construction in the Guidelines for Design and Construction of Hospitals to the extent possible as determined by the authority having jurisdiction: (1) A series of planned changes and updates to the physical plant of an existing facility (2) A renovation project that includes modification of an entire building or an entire area in a building to accommodate a new use or occupancy."
(C) Amend subsection 1.1-3.1.2.1 to read: “Where major structural elements make total compliance impractical or impossible, exceptions shall be considered in accordance with the Oregon Administrative Rules specific to the physical environment of the type of hospital under consideration.”
(D) Amend subsection 1.1-3.1.2.2 to read: "Minor renovation or replacement work shall be permitted to be exempted from the requirements in Section 1.1-3.1.1 (Compliance Requirements) provided they meet the criteria specified in OAR 333-675-0000 (Submission of Project Plans and Specifications for Review)(2) or (3) and do not reduce the level of health and safety in an existing facility."
(E) Amend subsection 1.1-3.1.4 to read: “Temporary Waivers When parts of an existing facility essential to continued overall facility operation cannot comply with particular standards during a renovation project, a temporary waiver of those standards shall be permitted as determined by the authority having jurisdiction if patient care and safety will not be jeopardized as a result. Reference Oregon Administrative Rules specific to the physical environment of the type of hospital under consideration.”
(F) Amend subsection A1.2-2.1.1 to read: “Functional program purpose. a. All projects, large and small, require a functional program to guide the design. The length and complexity of the functional program will vary greatly depending on project scope. b. The functional program can be used as a supplement to the construction documents; it is not intended to be approved by the authority having jurisdiction (AHJ).”
(G) Amend subsection 1.2-2.1.2.1 to read: “The governing body shall be responsible for having a functional program developed, documented, and updated. The governing body may delegate documentation of the functional program to consultants with subject matter expertise. The governing body shall review and approve the functional program.”
(H) Add subsection 1.2-2.2.7.4 and specify: “A description of the following: (a) Special design feature(s); (b) Occupant load, numbers of staff, patients, visitors and vendors; (c) Issue of privacy/confidentiality for patient; (d) In treatment areas, describe: (A) Types of procedures; (B) Design considerations for equipment; (C) Requirements where the circulation patterns are a function of asepsis control; and (D) Highest level of sedation, if applicable.”
(I) Amend subsection 1.2-4.1.1.2 to read: “To support this goal, an interdisciplinary team shall develop a safety risk assessment (SRA). A copy of the SRA shall accompany construction documents submitted to the Oregon Health Authority, Facility Planning and Safety Program.”
(J) Amend subsection 1.2-4.6.1 to read: “Behavioral and Mental Health Elements of the Safety Risk Assessment. The SRA report shall identify areas where patients at risk of mental health injury and suicide will be served. Elements of the assessment shall include but not be limited to: (1) A statement explaining the psychiatric population groups served; (2) A discussion of the capability for staff visual supervision of patient ancillary areas and corridors; (3) A discussion of the risks to patients, including self-injury, and the project solutions employed to minimize such risks; and (4) A discussion of building features and equipment, including items which may be used as weapons, that is intended to minimize risks to patients, staff and visitors.”
(K) Amend subparagraph (d) in subsection A1.2-5.4.5 to read: “d. In facilities with multi-bed rooms, family consultation rooms or grieving rooms, in addition to family lounges, should be provided to permit patients and families to communicate privately.”
(L) Amend subsection 2.1-2.8.2.1 to read: “This area shall include the following: (1) Space for counters (2) Hand-washing station(s) (a) At least one hand-washing station shall be provided within twenty feet and not through a door. See section 2.1-7.2.2.8 (Handwashing stations) for requirement.”
(M) Amend paragraph (1) in subsection 2.1-2.8.7.3 to read: “(1) At least one hand-washing station shall be provided for every four patient care stations or fewer.”
(N) Amend subsection 2.1-2.8.10.1 to read: “Ice-making equipment shall be of the self-dispensing type.”
(O) Amend subsection 2.1-4.2.8.7 to read: "Handwashing station. A hand-washing station(s) shall be provided within each separate room where open medication is prepared for administration except where prohibited. Placement shall be determined by OAR chapter 845, division 45; USP 797 and USP 800."
(P) Amend subsection 2.1-4.3.1.3 to read: "Regulations. Construction, equipment, and installation of food and nutrition service facilities in a hospital shall comply with the requirements of: (1) U.S. Food and Drug Administration (FDA) (2) U.S. Department of Agriculture (USDA) (3) Underwriters Laboratories, Inc. (UL) (4) NSF International (5) All offered dietary services shall comply with Oregon Health Authority, Food Sanitation Rules, OAR 333-150-0000 (Food Sanitation Rule) and other authorities having jurisdiction."
(Q) Amend paragraph (2) in subsection 2.1-5.2.2.2 to read: “(2) Laundry processing room. This room shall have space for commercial or industrial washing and drying equipment that can process at least a seven-day supply of laundry during the regularly scheduled work week. (a) Washers/extractors. Washers/extractors shall be located between the soiled linen receiving and clean processing areas. Washers/Extractors shall provide a temperature of at least 160 degrees Fahrenheit for a minimum of 25 minutes or include use of a chemical disinfectant. (b) Dryers (c) Supply storage. Storage shall be provided for laundry supplies.”
(R) Amend subsection 2.1-5.4.1.3 to read: "Regulated waste holding spaces (1) Secured space shall be provided for regulated medical waste and other regulated waste types. (a) Where provided as interior spaces, regulated medical waste or infectious waste holding spaces shall have cleanable floor and wall surfaces. (i) Wall base shall be integral and coved with the floor, tightly sealed to the wall, and constructed without voids that can harbor insects. (ii) Shall have hand sanitation dispenser in or adjacent to interior regulated waste storage spaces. (b) Where an exterior holding space is provided, it shall have the following: (i) Cleanable floor (and wall, where provided) surfaces (ii) Protection from weather (iii) Protection from animals (iv) Protection from vermin infestation (2) Such holding spaces shall provide: (a) Illumination per Illuminating Engineering Society of North America (IES) standards (b) Protection from unauthorized entry (3) Refrigeration requirements for such holding facilities shall comply with local and/or state regulations (4) Regulated waste management shall be in accordance with the requirements of OAR chapter 333, division 56."
(S) Amend subsection 2.1-6.2.7.1 to read: “Storage. A designated area located out of the required corridor width and directly accessible to the entrance shall be provided for storage of at least one wheelchair.”
(T) Add paragraph (4) to subsection 2.1-7.2.2.11 to read: "(4) All imaging facilities and radiation producing equipment installations must comply with OAR chapter 333, divisions 100 through 123, and be licensed by the Oregon Health Authority, Radiation Protection Services program."
(U) Amend subparagraph (7)(a) in subsection 2.1-7.2.3.1 to read: “(a) The room types listed in this section shall have floor and wall base assemblies that are monolithic and have an integral coved wall base that is carried up the wall a minimum of 6 inches (150 mm) and is tightly sealed to the wall. (i) Operating room (ii) Class 2 and Class 3 imaging rooms (iii) Cesarean delivery room (iv) Procedure rooms where cystoscopy, urology, and endoscopy procedures are performed (v) Endoscope processing room (vi) IV and chemotherapy preparation room (vii) Airborne infection isolation (AII) room (viii) Protective environment (PE) room (ix) Anteroom to AII and PE rooms, where provided (x) Sterile processing facility (xi) Bathing and toilet rooms (xii) Soiled workrooms and soiled hold rooms (xiii) Environmental services rooms”.
(V) Amend paragraph (2) in subsection 2.1-8.3.3.1 to read: “Stored fuel is required and storage capacity shall permit continuous operation for at least 96 hours.”
(6)(a) An applicant or a licensed SICF classified as a substance use disorder treatment facility shall comply with the following chapters of the 2018, FGI, Guidelines for the Design and Construction of Residential Health, Care and Support Facilities, adopted by reference including all references to part, subpart, sections, subsections, paragraphs, subparagraphs and appendices except as specified in subsections (6)(b) and (d) of this rule. References in FGI to “and/or” mean “or”.
(A) 1.1 – Introduction;
(B) 1.2 – Planning/Predesign Process;
(C) 1.3 – Site Selection;
(D) 1.4 – Design, Construction, and Commissioning Considerations and Requirements;
(E) 1.5 – Equipment;
(F) 2.1 – Site Elements;
(G) 2.2 – Design Criteria;
(H) 2.3 – Design Elements;
(I) 2.4 – Design and Construction Requirements;
(J) 2.5 – Building Systems; and
(K) 4.3 – Specific Requirements for Long-Term Residential Substance Abuse Treatment Facilities.
(b) The amendments specified in paragraphs (4)(c)(A) through (V) of this rule shall also apply to an SICF classified as a substance use disorder treatment facility.
(c) Section 2.3-4.2.2.4 of the 2018, FGI, Design and Construction of Residential Health, Care and Support Facilities, is not adopted by reference and does not apply under subsection (6)(a) of this rule.
(d) The following amendments or additions are made to the 2018, FGI, Guidelines for Design and Construction of Residential Health, Care and Support Facilities, as adopted and incorporated by reference under subsection (6)(a) of this rule. All references to part, subpart, sections, paragraphs, subparagraphs and appendices relate to the 2018, FGI, Guidelines for Design and Construction of Residential Health, Care and Support Facilities.
(A) Amend subsection A4.3-1.1.1.1 to read: “Long-term residential substance abuse treatment facility typology. Long-term residential treatment facilities may be located in a wide variety of settings including, but not limited to, a large suburban house, larger freestanding residential setting, or part of a nursing home, assisted living facility, homeless shelter, or facility in a prison. Only a large suburban house or larger freestanding residential setting shall be eligible for review within these guidelines for Special Inpatient Care Facility. The Authority does not have jurisdiction over other settings specified. Care is provided 24 hours a day, generally in non-clinical/acute care settings. This therapeutic community (TC) is a common type of long-term residential treatment setting for substance use disorders, which typically require 18 to 24 months of treatment, although funding and insurance limitations may reduce an individual’s stay to three, six, or 12 months. The focus of a TC is resocialization of an individual using the program’s entire community as active components of treatment. Addiction is viewed in the context of an individual’s social and psychological deficits, and treatment focuses on developing personal accountability and responsibility as well as socially productive lives. Treatment is typically highly structured and can be modified for specific care populations (e.g., adolescents, homeless residents, individuals from the criminal justice system, those with mental/behavioral issues). In addition to long-term residential treatment, a therapeutic community may offer shorter-term residential or outpatient treatment. A TC acquires a medical partner has an opportunity to become a federally qualified health center or a patient-centered medical home. A specialized type of treatment setting called a ’modified therapeutic community’ incorporates features of traditional therapeutic communities with a special focus on addressing co-occurring mental health conditions. Correctional institutions may incorporate in-prison TCs, and TCs are also available for people reentering society after being released from prison with the goal of reducing drug use and recidivism.”
(B) Amend paragraph (2) in subsection 4.3-2.2.2.2 to read: “A minimum of 70 square feet of floor space per bed is required in semi-private rooms and wards. A minimum of 100 square feet of floor space shall be provided in private rooms.”
(C) Amend subsection 4.3-2.2.2.7 to read: “Resident bathroom. Each resident shall have access to a bathroom. Bathroom doors shall comply with 2.4-2.2.4. (1) The bathroom shall contain the following: (a) Toilet (b) Hand-washing station. See Section 2.4-2.2.8 (Hand-Washing Stations) for requirements. (c) Mirror. See Section 2.4-2.2.8.7 (Mirror) for requirements. (d) Private individual storage for the personal effects of each resident. See Section 2.4-2.4.2 (Casework, Millwork, and Built-Ins) for requirements. (e) Shower. See Section 2.5-2.3.3.2 (Accessible showers) for requirements. (2) Where the bathroom is shared, privacy locks shall be permitted with provisions for emergency access.”
(D) Add subsection 4.3-2.2.3.4 to read: “Detoxification Room. The design and need for a detoxification room shall be described in the Resident Safety Risk Assessment and functional program. Where provided, a minimum of one residing patient room for detoxification, located to allow direct observation by nursing staff, shall be provided. Windows in detoxification rooms shall be of a security type that can only be opened by keys or tools that are under the control of the staff. An adjoining or closely available toilet and hand washing lavatory is also required serving detoxification residing patients only. This room shall be designed with special consideration that residing patient is incapable of self-preservation in an emergency.”
(E) Amend subsection 4.3-2.3.8.1 to read: “Outdoor spaces shall be provided for residents, visitors, and staff. The design and use of outdoor activity spaces shall be described in the Resident Safety Risk Assessment.”
(F) Amend subsection 4.3-4.5.3.1 to read: "Where an outside vendor is used to provide meals for a setting of 16 or more beds, dedicated space and equipment shall be provided for a warming kitchen, including space for minimal equipment for preparation of breakfast, emergency, or after-hours meals. These facilities serving 16 or more beds shall comply with OAR 333-150-0000 (Food Sanitation Rule) (Food Sanitation Rules) including the provisions for commercial-grade equipment, space, and policies."
(G) Amend subsection 4.3-4.5.4 to read: "Decentralized Kitchen Where food preparation is conducted on-site for 16 or more beds, the facility shall have dedicated non-public staff space and equipment for preparation of meals. See section 2.3-2.3.4 (Resident and Participant Kitchen) for requirements. These facilities serving 16 or more beds shall comply with OAR 333-150-0000 (Food Sanitation Rule) (Food Sanitation Rules) including the provisions for commercial-grade equipment, space, and policies."
(H) In subsection 4.3-4.6.3.2:
(i) Amend subparagraph (2)(c) to read: “(c) Rooms used for processing shall have a flushing-rim sink and a handwash sink.”
(ii) Add paragraph (6) to read: “(6) Washers/extractors. Washers/extractors shall be located between the soiled linen receiving and clean processing areas. Washers/Extractors shall provide a temperature of at least 160 degrees Fahrenheit for a minimum of 25 minutes or include use of a chemical disinfectant.”
(I) Amend subsection 4.3-5.2.2.4 to read: “Doors and door hardware See Section 2.4-2.2.4 (Doors and Door Hardware) for requirements in addition to those in this section.”
(7) An SICF classified as a religious institution must be designed, constructed, and maintained to ensure the safety of the patients, staff, and the public and shall comply with the following:
(a) General Building. The overall environment must be maintained in a manner that ensures the safety and well-being of the patients. The institution must have the following:
(A) Procedures for the proper storage and disposal of trash;
(B) Proper ventilation and temperature control and appropriate lighting levels to ensure a safe and secure environment;
(C) An effective pest control program including that:
(i) Wall openings for pipes, ducts, and conduits as well as joints at structural elements shall be sealed; and
(ii) In dietary and food storage areas, wall construction, finish, and trim, including joints between walls and floors, shall be free of insect- and rodent-harboring spaces;
(D) A preventive maintenance program to maintain essential mechanical, electrical, and fire protection equipment operating in an efficient and safe manner; and
(E) A working call system for patients to summon aid or assistance.
(b) Patient rooms. Patient rooms must be designed and equipped for adequate care, comfort, and privacy of the patient and shall meet the following conditions:
(A) Accommodate no more than four patients;
(B) Measure at least 80 square feet per patient in multiple patient rooms and at least 100 square feet in single patient rooms;
(C) Have direct access to an exit corridor;
(D) Be designed or equipped to assure full visual privacy for each patient. Design for privacy shall not restrict patient access to the toilet, room entrance, window, or other shared common areas in the patient room;
(E) Have at least one operable window to the outside, provided with window coverings;
(F) Have a floor at or above grade level; and
(G) Be furnished with the following:
(i) A separate bed of proper size and height for the convenience of the patient;
(ii) A clean, comfortable mattress and pillow with protective coverings;
(iii) Bedding appropriate to the weather and climate; and
(iv) Functional furniture appropriate to the patient’s needs and individual closet space with clothes racks and shelves accessible to the patient.
(c) Plumbing and Sanitary Environment.
(A) Each patient shall have access to a toilet room without entering the general corridor area. One toilet room shall serve no more than four beds and no more than two patient rooms.
(i) The toilet room shall contain a toilet and a handwash station.
(ii) Doors to all rooms containing bathtubs, showers, and toilets for patient use shall be hinged, sliding, or folding with door hardware that allows staff access. Where swinging doors are provided, the door shall swing outward or be provided with emergency rescue (dual-swing) hardware.
(B) Adequate handwashing stations shall be provided for the total facility population and include lavatories with hot and cold running water, soap, and single use sanitary towels.
(i) A hand-washing station shall be provided both in the patient room and the toilet room. This hand-washing station shall be located at or adjacent to the entrance to the patient room with unobstructed access for use by health care personnel and others entering and leaving the room. When multi-patient rooms are permitted, this station shall be located outside the patients’ cubicle curtains.
(ii) At least one hand-washing station shall be provided for the administrative center or nurses’ station that is within 20 feet and not through a door.
(C) Bathing facilities for patients shall be provided to include at least one shower or tub for each eight beds, serving patient rooms not containing bathing facilities directly adjoining the room. Bathing facilities shall include space for drying, dressing, grooming, and a surface to temporarily place toiletries.
(D) An institution licensed for more than 16 patients must provide at least one separate toilet and hand wash lavatory for staff and visitor use. The staff and visitor toilet shall not be located where it would require a visitor to travel through any intervening staff support areas.
(E) There shall be an environmental services room with floor or service sink and space for temporary storage of refuse. An institution licensed for 16 or fewer patients may combine this room with other soiled rooms.
(F) Cart sanitizing facilities and cart storage area for both dietary and linen services shall be available.
(G) Areas subject to frequent wet cleaning methods or high amounts of moisture, including but not limited to, kitchens, soiled workrooms, soiled and clean utility rooms, environmental services rooms and toilet rooms, shall meet the following requirements:
(i) The floors and wall bases shall be constructed of slip-resistant materials that are not physically affected by germicidal or other types of cleaning solutions.
(ii) Floors shall be homogeneous and have sealed joints.
(iii) Wall bases shall be continuous, integral or sealed to the floor and the wall, and constructed without voids.
(iv) Wall surfaces in areas routinely subjected to wet spray or splatter (for example, kitchens, soiled linen processing, environmental services room) shall be smooth, scrubbable, and water-resistant.
(v) Ceiling surfaces in dietary and laundry areas, bathrooms, central bathing rooms or areas with showers, soiled utility rooms, and environmental services rooms shall be impervious and moisture-resistant.
(d) There shall be a clean storage room or enclosed cabinet spaces for supplies and equipment.
(e) Space for patient dining at a minimum of 28 square feet per patient shall be provided.
(f) A room or space for social activities which may include group therapy or other gatherings at a minimum of 15 square feet per patient shall be provided. This space may be omitted if the institution is licensed for a capacity of 16 or fewer and social space is accommodated within the shared patient dining.
(g) There shall be an administrative center or nurse station. This space shall include provisions for storage of administrative supplies, a worksurface with equipment for documentation, and secure storage of staff personal belongings.
(h) Patients shall have access to a telephone and accommodations shall be made to allow private conversations.
(i) Food and nutrition services. The facility may provide onsite or third party contracted dietary services. All offered dietary services shall comply with Oregon Health Authority, Food Sanitation Rules, chapter 333, division 150 and other authorities having jurisdiction.
(A) Onsite dietary service in an institution licensed for a capacity of 16 or fewer may be of residential type except as required by the building codes. Kitchen facilities and equipment in an institution licensed for a capacity of more than 16 must be commercial type equipment. The following must be provided:
(i) A dishwasher;
(ii) A pot wash sink (unless all pots are sanitized in the dishwasher);
(iii) A food prep sink;
(iv) A separate hand wash lavatory;
(v) Stove and oven equipment for cooking and baking needs;
(vi) Self-dispensing ice-making equipment;
(vii) Refrigerator(s) and freezer(s);
(viii) Storage for a mop and other cleaning tools and supplies used for dietary areas must be separate from those used in toilet rooms, patient rooms, and other support areas. In an institution with a capacity of more than 16, a separate janitor closet or alcove must be provided with a floor or service sink and storage for cleaning tools and supplies; and
(B) Third-party contracted dietary services:
(i) Provisions shall be made to prevent contamination, keep hot and cold foods at required temperature ranges in transit and on site prior to consumption.
(ii) If ware washing is provided on site, either a three-compartment sink or dishwasher (commercial grade if the institution is licensed for a capacity of more than 16) shall be provided.
(iii) Nourishment area: There shall be a handwash station, food prep sink (if required by the functional program), work counter, refrigerator, storage cabinets, and equipment for serving nourishment as required by the functional program.
(j) Linen services:
(A) On-Site Processing. If linen is to be processed on the site, the following shall be provided:
(i) Soiled linen utility room with adequate space for receiving and sorting. Room(s) shall have ventilation and exhaust, a clinical sink or equivalent flushing-rim fixture with a rinsing hose or bedpan washer, handwash station, and space for linen and containers;
(ii) Laundry processing room with commercial-type washing and drying equipment. Washers/extractors shall be located between the soiled linen receiving and clean processing areas. Washers/extractors shall provide a temperature of at least 160 degrees Fahrenheit for a minimum of 25 minutes or include use of a chemical disinfectant;
(iii) Secure storage for laundry supplies;
(iv) Clean linen inspection and mending room or area; and
(v) Clean linen storage, issuing, and holding room or area.
(B) If linen is processed off-site, the following shall be provided:
(i) Soiled linen holding room with ventilation and exhaust; and
(ii) Clean linen receiving, holding, inspection, and storage room(s).
(8) The Authority may, upon written request, allow variations from these requirements (other than fire and life safety requirements) when conditions make certain changes to an SICF impractical to accomplish, as long as the intent of the requirement is met, and the care and safety of patients will not be jeopardized. An applicant or SICF must obtain written approval from the Authority in accordance with OAR 333-071-0260 (Waivers), for any minor variation.
(9) An SICF shall conform to the editions of the Oregon State Building Code, as defined in ORS 455.010 (Definitions for ORS chapter 455)(8), under which they were constructed. SICFs to be certified for Medicare reimbursement shall meet standards of the 2012, National Fire Protection Association (NFPA) #101 and #99 Codes.

Source: Rule 333-071-0580 — Physical Environment Requirements, https://secure.­sos.­state.­or.­us/oard/view.­action?ruleNumber=333-071-0580.

333‑071‑0200
Purpose and Applicability
333‑071‑0205
Definitions
333‑071‑0210
License Application and Fees
333‑071‑0215
Application Review
333‑071‑0220
Approval of License Application
333‑071‑0225
Fees for Complaint Investigations and Compliance Surveys
333‑071‑0230
Expiration and Renewal of License
333‑071‑0235
Denial of License Application
333‑071‑0240
Return of SICF License and SICF Closure
333‑071‑0245
Discontinuance and Recommencement of Operations
333‑071‑0250
Classification
333‑071‑0260
Waivers
333‑071‑0270
Complaints
333‑071‑0280
Investigations
333‑071‑0290
Surveys
333‑071‑0300
Nurse Staffing Audit and Complaint Investigation Procedures
333‑071‑0310
Violations
333‑071‑0315
Informal Enforcement
333‑071‑0320
Formal Enforcement
333‑071‑0330
Approval of Accrediting Organization
333‑071‑0340
Civil Penalties for Violations of Nurse Staffing Laws
333‑071‑0345
Civil Penalties for Violation of Smoking Prohibition
333‑071‑0350
Civil Penalties, Generally
333‑071‑0360
Governing Body Responsibility
333‑071‑0370
Health Care Practitioner Credentialing
333‑071‑0380
Administrator
333‑071‑0390
Medical Staff
333‑071‑0400
Organization Policies
333‑071‑0410
Patient Rights
333‑071‑0420
Personnel
333‑071‑0430
Medical Records
333‑071‑0440
Quality Assessment and Performance Improvement
333‑071‑0450
Infection Control
333‑071‑0470
Patient Admission and Treatment Orders
333‑071‑0480
Nursing Care Management
333‑071‑0485
Nursing Services
333‑071‑0490
Nurse Executive
333‑071‑0510
Dietary Services
333‑071‑0520
Laboratory Services
333‑071‑0530
Pharmacy Services
333‑071‑0535
Radiology Services
333‑071‑0550
Sanitary Precautions
333‑071‑0560
Safety and Emergency Preparedness
333‑071‑0570
Smoking Prohibition
333‑071‑0580
Physical Environment Requirements
Last Updated

Jun. 8, 2021

Rule 333-071-0580’s source at or​.us